Listar FRCU - GIS: Grupo de Ingeniería de Superficies por título
Mostrando ítems 111-130 de 134
-
Plasma nitriding and plasma nitrocarburizing of a low alloy steel selected to produce camshafts for diesel engines
(2015-05-14)Camshafts are a relevant part of diesel engines of extended use today. These components work under torsion and are also prone to fatigue and wear damage. Usually they are manufactured by casting, forging or machining from ... -
Plasma nitriding plus oxidizing as a protective treatment for AISI 4140 steel
(2022-09-29)AISI 4140 is a typical chromium molybdenum medium alloy steel, widely used as construction steel for machine components. Plasma nitriding has been applied as surface hardening treatment with success but the nitrided layer ... -
Plasma surface engineering to enhance wear and corrosion resistance of stainless steels
(2014-11-11)A brief description of the research lines of the Surface Engineering Group of UTN will be presented, as well as some important results obtained in the last years concerning plasma nitriding of austenitic stainless steel ... -
Propiedades tribológicas y mecánicas de los recubrimientos en base carbono tipo DLC
(2017-08-17)Los recubrimientos hidrogenados en base crbono tipo DLC (Diamond Like Carbon), son depositados sobre diferentes aceros y resultan atractivos por su excelente comportamiento tribológico, bajo coeficiente de fricción, alta ... -
Protección de acero para instrumentos quirúrgicos con recubrimientos duros en base carbono tipo DLC
(2018-07-19)Los aceros inoxidables martensíticos como el AISI 420 tienen múltiples aplicaciones, entre ellas instrumentos quirúrgicos, donde se requiere buena resistencia al desgaste y a la corrosión. Los tratamientos de modificación ... -
Protección de acero para instrumentos quirúrgicos con recubrimientos duros en base carbono tipo DLC
(2016-11-22)Los aceros inoxidables martensíticos como el AISI 420 tienen múltiples aplicaciones, entre ellas instrumentos quirúrgicos, donde se requiere buena resistencia al desgaste y a la corrosión. Los tratamientos de modificación ... -
Rayado sobre acero SAE 4140 recubierto con TiN. Influencia del nitrurado iónico previo
(Comisión Nacional de Energía Atómica, 2018-10-05)En este trabajo, se estudió el desempeño de probetas de acero SAE 4140 con diferentes combinaciones de tratamiento, a través de ensayos de indentación y rayado. Sobre un primer grupo de probetas se aplicó un recubrimiento ... -
Recubrimientos duros tipo DLC depositados sobre acero inoxidable martensítico nitrurado : análisis de adhesión y resistencia a la corrosión
(2014-10-21)Los tratamientos de modificación superficial como la nitruración permiten mejorar las propiedades tribológicas del acero AISI 420 pero afectan la resistencia a la corrosión. Los recubrimientos tipo DLC (“Diamond Like ... -
Recubrimientos duros tipo DLC depositados sobre acero inoxidable martensítico nitrurado: análisis de adhesión y resistencia a la corrosión
(Universidad Nacional del Litoral., 2015)Los tratamientos de modificación superficial como la nitruración permiten mejorar las propiedades tribológicas del acero AISI 420 pero afectan la resistencia a la corrosión. Los recubrimientos tipo DLC (“Diamond Like ... -
Recubrimientos en base carbono tipo "DLC" características, propiedades y aplicaciones
(Asociación Argentina de Tribología, 2016-08)El DLC (“Diamond Like Carbon”) es un recubrimiento fino en base a carbono similar al diamante, que posee excelentes propiedades mecánicas, térmicas, electrónicas y ópticas. Entre las aplicaciones en el área mecánica, se ... -
Resistencia al desgaste y corrosión de AISI 316L nitrurado por dos diferentes métodos asistidos por plasma
(2014-10-21)El acero inoxidable austenítico AISI 316L, muy requerido por la industria química y alimenticia, entre otras, presenta una excelente resistencia a la corrosión pero su baja dureza y resistencia al desgaste limitan sus ... -
Resistencia al desgaste y corrosión de AISI 316L nitrurado por dos diferentes métodos asistidos por plasma
(Universidad Nacional del Litoral., 2014-10)El acero inoxidable austenítico AISI 316L, muy requerido por la industria química y alimenticia, entre otras, presenta una excelente resistencia a la corrosión pero su baja dureza y resistencia al desgaste limitan sus ... -
Resistencia al desgaste y corrosión de AISI 316L nitrurado por plasma y recubierto con TiN
(2014-05-15)En este trabajo se presentan los resultados de desgaste y corrosión realizados sobre acero AISI 316L nitrurado por plasma y recubierto con nitruro de titanio con la técnica de PVD por arco de plasma. -
Soft and thick DLC deposited on AISI 316L stainless steel with nitriding as pre-treatment tested in severe wear conditions
(2020)Thick and soft DLC coatings were deposited over stainless steel to improve their surface properties, protecting them from wear in different conditions. When a protective film is thick, it can be considered as selfsustaining ... -
The EU-RISE project CREATe-Network - Composites for resource-efficient applications and technologies
(2018-09-28)The aim of the EU-RISE project CREATe-Network is to provide a platform for international and intersectoral collaboration between different academic and non-academic institutions in Europe, Latin America, USA and South ... -
Thermal stability of DLC coating deposited on precipitation hardening stainless steels
(2015-11-17)Relationship between nanohardness and annealing temperature of DLC coating on duplex (previously nitrided) and only coated PH steel samples. -
Tribological and corrosion Behavior of Duplex Coated AISI 316L using plasma based ion implantation and deposItion
(2020)The implementation of a duplex process, which combines plasma nitriding with hard coatings obtained by cathodic arc, on stainless steel substrates has faced adhesion problems that affected the wear and corrosion behavior ... -
Tribological behavior of thick and soft DLC coatings
(2015-05-13)Austenitic stainless steels are widely used in industry due to their good corrosion resistance; however, they present poor mechanical properties. Different coatings such as DLC “Diamond Like Carbon” can be used in order ... -
Tribological behaviour of a multilayer CrN/DLC coating obtained using PVD-MS
(2022-08)Diamond-like Carbon (DLC) coatings are used as protective layers for steel components due to their hardness, chemical inertia and interesting tribological properties. Reducing wear and friction coefficient is of great ... -
Tribological behaviour of TiAlN and AlCrN coatings deposited over martensitic stainless steel
(2023-04-26)In this work, the tribological behaviour of PVD TiAlN and AlCrN coatings deposited on AISI martensitic stainless steel is studied. The coatings were deposited by cathodic arc PVD in Oerlikon Balzers Argentina.